Under Construction
| Enter Program | 1. Short J16 pins for 2 seconds 2. Enter 6653 3. Keypad should show "Programmer" |
| Move forward | Command button |
| Move backwards | Back arrow key |
| Exit Program | Press Command key until you see STOP then press top row key to exit |
| Download Answer | Press 984 Command, then select top row key for (pickup) |
| 2.1 | Initialization | This function allows you to set the panel’s programmed memory back to the factory defaults in preparation for system programming. After you select YES to clear a section of memory, the panel asks if you are sure you want to clear the memory. This is a safeguard against accidently erasing part of your programming. No memory is cleared from the programming until you answer YES to the SURE? YES NO prompt. | ||||||||||||||||||||
| 2.2 | CLEAR ALL CODES | NO leaves existing codes intact YES clears the user code memory and assigns the user code number 99 to user 30 on the XT30, and 99 on the XT50 |
||||||||||||||||||||
| 2.3 | CLEAR ALL SCHEDULES | NO - Leaves existing schedules intact YES - Clears all schedules from the XT30 or XT50 programming |
||||||||||||||||||||
| 2.4 | CLEAR EVENTS | NO leaves existing event memory intact YES clears all event memory currently held in the panel’s Display Events buffer. |
||||||||||||||||||||
| 2.5 | CLEAR ZONE PROGRAMMING | NO leaves existing zone information intact YES sets all zones in the system to * UNUSED * |
||||||||||||||||||||
| 2.6 | CLEAR COMMUNICATIONS | NO - Leaves existing communication, network, and email programming intact YES - Clears communication, network and email programming to factory defaults |
||||||||||||||||||||
| 2.7 | SET TO FACTORY DEFAULTS | NO leaves the remainder of the existing panel programming intact YES sets the panel’s programming back to factory default selections. Selecting DEFAULTS does not clear the panel’s event memory, zone or user code information, or schedules. |
||||||||||||||||||||
| 3.1 | Communications | The Communication section allows you to configure the communication settings for the XT30/XT50 panel. After choosing the Communication Type, continue through the list of options | ||||||||||||||||||||
| 3.2 | ACCOUNT NUMBER | 4 or 5 digit account number 4 Digits for CID 5 Digits for DMP format Enter the account number sent to the receiver DD, NET, CELL - The range of account numbers for Digital Dialer, Network, and Cell is 1 to 65535. For account numbers of four digits or less, you do not have to enter leading zeros. The panel automatically right justifies the account number CID - The account number range for this format is 1 - 9999. | ||||||||||||||||||||
| 3.3 | XMIT DELAY | Enter the number of seconds (15 to 45 seconds) the panel waits before sending burglary alarm reports to the receiver. The bell and relay outputs are not delayed during this period. Program Burglary Outputs for steady, and set Abort Reports to YES if Opening and Closing reports are not being sent. Enter 0 (zero) to disable this function. The default is 30. If the area where the alarm occurred is disarmed during the Transmit Delay time, only an Abort Report (S45) message is sent to the receiver. If the area where the alarm occurred is disarmed after the alarm message is sent to the receiver but before the Bell Cutoff time expires, even if the alarm was silenced, an Alarm Cancelled (S49) message is sent. The Alarm Cancelled report cannot be disabled. | ||||||||||||||||||||
| 3.4 | COMM TYPE | DD= Digitial Dialer CID= Contact I.D. NET= Network Communications CELL= Cellular Communication NONE= For local system | ||||||||||||||||||||
| 3.5 | BACKUP DIALER | Backup Dialer option is available if COMM TYPE is set for NET. The Backup Dialer tries to send the message after the main communication fails for 60 seconds on NET. If the backup dialer fails then the message is discarded | ||||||||||||||||||||
| 3.6 | BACK UP CELL | Backup Cellular option is available if COMM TYPE is set for NET or DD/CID. The Backup Cellular tries to send the message after the main communication fails for 60 seconds on NET and 10 dial attempts with DD/CID. If the backup dialer fails then the message is discarded | ||||||||||||||||||||
| 3.7 | TEST TIME | Press COMMAND to enter the Test Time. Enter the time of day the panel sends the test report to the SCS-1R Receiver. Use entries between 12:00 to 11:59 and then choose AM or PM | ||||||||||||||||||||
| 3.8 | NET TEST DAYS: DAIL TEST DAYS CELL TEST DAYS | Enter how often the panel test report is sent Enter how often the panel test report is sent to the receiver for each communication type programmed. Enter from 1 to 60 days. Enter zero to disable the test report. Default is 1 (one) day. These options only display if a test time is entered and that particular communication method is being used | ||||||||||||||||||||
| 3.9 | CHECKIN | Enter the number of minutes (15 to 240) between check-in reports for Net Communication. Check-in reports are a method of supervising the panel for communication with the receiver for Net communication. Enter 0 (zero) to disable this feature. The default Check -in Time is 200 minutes. | ||||||||||||||||||||
| 3.10 | FAIL TIME | Fail Time allows the receiver to miss a defined number of check-ins before logging that the panel is missing. For example, if checkin is 20 and Fail TIME is 30, the receiver only indicates a Panel Not Responding after 30 minutes. The Fail TIME must be equal to or greater than the CHECKIN minutes: If the CHECKIN is 20 minutes, the FAIL TIME must be 20 or more. The maximum FAIL TIME is 240 minutes. The default failfail TIME is 240 minutes. | ||||||||||||||||||||
| 3.11 | COMM TROUBLE | Enable communication fail notification by selecting YES at COMM TRBL. Select NO to disable. Default is YES.
When COMM TRBL is YES and the panel detects a failure of communication, the panel sends an S72 (Comm Trouble) message through a backup communication method with notification of the failure. If both primary and secondary methods of communication fail, then two S72 messages will be sent via the third communication method, if programmed. The keypad sounds a continuous tone, which may be silenced by pressing any key, and displays “COMM -TRBL”.
When communication is restored, the panel sends an S73 (Comm Restored) message through the primary communication. The “COMM -TRBL” message is removed from the keypad display and the keypad sounder is turned off, if no other trouble messages are pending. | ||||||||||||||||||||
| 3.12 | FIRST GPRS APN | Enter the first APN (Access Point Name). This allows an access point for cellular communication and is used to connect to a DNS network. The APN may contain two lines of 16 characters to equal 32 characters. Default is set to SECURECOM400 | ||||||||||||||||||||
| 3.13 | SECOND GPRS APN | Enter the second APN (Access Point Name). This works as a backup in case the first APN fails. The APN may contain two lines of 16 characters to equal 32 character Default is set to SECURECOM400 /td> | ||||||||||||||||||||
| 3.14 | RECIEVER 1 PROG | Allows you to set the options for the first receiver the XT30/XT50 panel attempts to contact when sending reports. The XT30/XT50 supports communication to two receivers | ||||||||||||||||||||
| 3.15 | ALARM | YES enables Abort, Alarm, Alarm Restoral, Alarm Bell Silenced, Ambush, Exit Error, and System Recently Armed reports to be sent to this receiver. Default is YES. | ||||||||||||||||||||
| 3.16 | SPV/TRBL | YES enables Supervisory, Trouble, Trouble Restoral, Force Armed, Late to Close, and Fault reports to be sent to this receiver. Default is YES | ||||||||||||||||||||
| 3.17 | O/C USER | YES enables Opening/Closing, Door Access, Schedule and Code Changes, Bypass, and Sensor Reset reports by user to be sent to this receiver. Default is YES. No | ||||||||||||||||||||
| 3.18 | TEST RPT | Enter YES to enable the Recall Test report to be sent to this receiver | ||||||||||||||||||||
| 3.19 | FIRST PHONE NO. | Enter the first number the panel dials to send reports to this receiver. A phone number may contain two lines of 16 characters to equal 32 characters. You can program a three-second pause in the dialing sequence by entering P. Program a dial tone detect by entering D. These characters are counted as part of the 32 characters. Call Waiting: You can place the “* 7 0 P” (Star, Seven, Zero, Pause) in the telephone number first position to cancel Call Waiting. For example, program NET with second line DD and phone number *70P555-1212, and you have NET with Call Waiting cancelled on the second line. Caution: A call waiting cancel programmed on a non-call waiting telephone line would prevent communication to the central station | ||||||||||||||||||||
| 3.20 | SECOND PHONE NO. | The panel dials the second number after two successive attempts failed using the first number. If the panel cannot reach this receiver after two attempts using the second number, it returns to the first number and makes two additional attempts. A total of ten dialing attempts are made using the first and second phone numbers. If a second phone number is not entered, the first phone number is used for all dialing attempts. Each number can be up two lines of 16 characters to equal 32 characters in length, including any P, D, or *70P characters entered for pause, dial tone detect, or call waiting cancel option | ||||||||||||||||||||
| 3.21 | FIRST I.P. ADDR | Enter the first (primary) IP address where the panel sends network or cell messages. The IP address must be unique and cannot be duplicated on the network. Enter all 12 digits and leave out the periods. For example, enter IP address 192.168.0.250 as 192168000250. The periods display automatically. For NET: The first and second IP addresses are alternately used for 8-second intervals until successful communication or 1 minute elapses. For Cell: The message is sent using First GPRS APN and the First IP Address. If no acknowledgment is received, First GPRS APN and the Second IP address are used, followed, if needed, by Second GPRS APN and first and second IP addresses, respectively | ||||||||||||||||||||
| 3.22 | FIRST I.P. PORT | Enter the first IP port number to be used in conjunction with the First IP Address. The IP port identifies the port used to communicate messages to and from the panel. The default IP Port setting is 2001 | ||||||||||||||||||||
| 3.23 | SECOND I.P. ADDR | Enter the second IP address where the panel sends network messages. The IP Address must be unique and cannot be duplicated on the network. Enter all 12 digits and leave out the periods. For example, enter IP address 192.168.0.250 as 192168000250. The periods display automatically | ||||||||||||||||||||
| 3.24 | SECOND I.P. PORT | Enter the second IP port number to be used in conjunction with the Second IP Address. The IP port identifies the port used to communicate messages to and from the panel. The default IP Port setting is 2001 | ||||||||||||||||||||
| 3.25 | RECIEVER 2 PROG | Allows you to set the options for the second receiver the XT30/XT50 panel attempts to contact when sending reports. The XT30/XT50 supports communication to two receivers. If you select YES for any of the Receiver 2 options, you must have at least one phone number or IP address programmed in Receiver 2 programming. Receiver 2 defaults are set to NO | ||||||||||||||||||||
| 3.26 | ALARM | YES enables Abort, Alarm, Alarm Restoral, Alarm Bell Silenced, Ambush, Exit Error, and System Recently Armed reports to be sent to this receiver. Default is NO | ||||||||||||||||||||
| 3.27 | SPV/TRBL | YES enables Supervisory, Trouble, Trouble Restoral, Force Armed, Late to Close, and Fault reports to be sent to this receiver. Default is NO | ||||||||||||||||||||
| 3.28 | O/C USER | YES enables Opening/Closing, Door Access, Schedule and Code Changes, Bypass, and Sensor Reset reports by user to be sent to this receiver. Default is NO | ||||||||||||||||||||
| 3.29 | TEST RPT | YES enables the Recall Test report to be sent to this receiver. Default is NO | ||||||||||||||||||||
| 3.30 | FIRST PHONE NO. | Enter the first number the panel dials to send reports to this receiver. A phone number may contain two lines of 16 characters to equal 32 characters. You can program a three-second pause in the dialing sequence by entering P. Program a dial tone detect by entering D. These characters are counted as part of the 32 characters. Call Waiting: You can place the “* 7 0 P” (Star, Seven, Zero, Pause) in the telephone number first position to cancel Call Waiting. For example, program NET with second line DD and phone number *70P555-1212, and you have NET with Call Waiting cancelled on the second line. Caution: A call waiting cancel programmed on a non-call waiting telephone line would prevent communication to the central station | ||||||||||||||||||||
| 3.31 | SECOND PHONE NO. | The panel dials the second number after two successive attempts failed using the first number. If the panel cannot reach this receiver after two attempts using the second number, it returns to the first number and makes two additional attempts. A total of ten dialing attempts are made using the first and second phone numbers. If a second phone number is not entered, the first phone number is used for all dialing attempts. Each number can be up two lines of 16 characters to equal 32 characters in length, including any P, D, or *70P characters entered for pause, dial tone detect, or call waiting cancel option | ||||||||||||||||||||
| 3.32 | FIRST I.P. ADDR | Enter the first (primary) IP address where the panel sends network or cell messages. The IP address must be unique and cannot be duplicated on the network. Enter all 12 digits and leave out the periods. For example, enter IP address 192.168.0.250 as 192168000250. The periods display automatically. For NET: The first and second IP addresses are alternately used for 8-second intervals until successful communication or 1 minute elapses. For Cell: The message is sent using First GPRS APN and the First IP Address. If no acknowledgment is received, First GPRS APN and the Second IP address are used, followed, if needed, by Second GPRS APN and first and second IP addresses, respectively | ||||||||||||||||||||
| 3.33 | FIRST I.P. PORT | Enter the first IP port number to be used in conjunction with the First IP Address. The IP port identifies the port used to communicate messages to and from the panel. The default IP Port setting is 2001 | ||||||||||||||||||||
| 3.34 | SECOND I.P. ADDR | Enter the second IP address where the panel sends network messages. The IP Address must be unique and cannot be duplicated on the network. Enter all 12 digits and leave out the periods. For example, enter IP address 192.168.0.250 as 192168000250. The periods display automatically | ||||||||||||||||||||
| 3.35 | SECOND I.P. PORT | Enter the second IP port number to be used in conjunction with the Second IP Address. The IP port identifies the port used to communicate messages to and from the panel. The default IP Port setting is 2001 | ||||||||||||||||||||
| Network Options | Network Options are provided to define the network configuration for the panel. This information will be used during communication of messages via network or email. Note: IP addresses and port numbers may need to be assigned by the network administrator. When entering an IP, Gateway, or Subnet Mask address be sure to enter all 12 digits and leave out the periods. For example, IP address 192.168.000.250 is entered as 192168000250. | |||||||||||||||||||||
| 4.1 | DHCP MODE ENABLE | If the panel uses a dynamic IP address Select YES. When set to YES the panel will operate in DHCP and will not use the Local IP Address number. When the DHCP option is set to NO, the panel will use the IP address entered in Local IP Address. The default value for DHCP mode is YES | ||||||||||||||||||||
| 4.2 | LOCAL I.P. ADDR | Enter the local IP address for the panel. The Local IP Address must be unique and cannot be duplicated on the network. The default local IP address is 192.168.0.250 | ||||||||||||||||||||
| 4.3 | GATEWAY ADDR | Enter the local gateway address. The Gateway IP Address is needed to exit the local network. The default gateway address is 192.168.0.1. | ||||||||||||||||||||
| 4.4 | SUBNET MASK | Enter the local subnet mask assigned to the panel. The default subnet mask address is 255.255.255.000. | ||||||||||||||||||||
| 4.5 | DNS SERVER | Enter the IP address of the DNS (Domain Name System) used by the panel to resolve domain names into IP addresses. The default address is 0.0.0.0. | ||||||||||||||||||||
| 4.6 | PROGRAMMING PORT | Enter the programming port number. The programming port identifies the port used to communicate messages to and from the panel. The default Programming Port setting is 2001 | ||||||||||||||||||||
| Messaging Setup | ||||||||||||||||||||||
| 5.1 | MESSENGING SETUP | This section allows you to enter the information needed to send and receive messages directly to and from the panel via email and MyAccess™ text messaging using network or cellular communication. All of the name and password options below allow up to 32 lowercase characters to be entered. The Destination addresses allow up to 48 characters to be entered. System Name is displayed with initial caps - Zone Alarm - Zone Troubles - Zone Bypassing by user - Arming/disarming - Late to close - Late to open - Early to close - A/C Power trouble and Restoral - System Low Battery - Ambush (Duress) - Cancel - Check-in by user | ||||||||||||||||||||
| 5.2 | ENABLE MESSENGING | Select YES to allow the panel to send messages to three programmed destinations. Default is NO | ||||||||||||||||||||
| 5.3 | SYSTEM NAME | Enter a unique name for the panel. The panel name will be used as the sender of the message. The text entered will be displayed with initial caps. If this field is left blank, the panel account number will be sent | ||||||||||||||||||||
| 5.4 | DESTINATION 1 | Enter the first email address or cell phone number where messages will be sent. The message can be sent to any device (computer, cell phone, PDA) as long as a valid email address or cell phone number is entered. When entering email addresses, press the 7 digit key followed by the fourth Select Key to add the @ symbol and the 9 digit key followed by the fourth Select Key to add the _ symbol. See the Entering Non-Alpha Characters section for additional symbols. Note: Mail servers that require Transport Layer Security (TLS) encryption are not supported by the XT30/XT50. | ||||||||||||||||||||
| 5.5 | DESTINATION 1 USER NUMBER | If Destination 1 is a 10-digit cellular number, enter a user’s user number from this account. This option is used when sending commands such as arming or disarming back to the panel using MyAccess™ text messaging from the same cell phone or PDA. The user number must have the authority to perform the commands as if it occurred at the keypad. MyAccess™ text command operation is available in XT30/XT50 Series panels using version 102 or higher. Entering 0 (zero) disables this option. Default is 0 | ||||||||||||||||||||
| 5.6 | DESTINATION 2 | |||||||||||||||||||||
| 5.7 | DESTINATION 2 USER NUMBER | If Destination 2 is a cellular number, enter the user's User number for the arming/disarming authorization | ||||||||||||||||||||
| 5.8 | DESTINATION 3 | Enter the third destination email address or cell phone number | ||||||||||||||||||||
| 5.9 | DESTINATION 3 USER NUMBER | If Destination 3 is a cellular number, enter the user's User number for the arming/disarming authorization | ||||||||||||||||||||
| 5.10 | EMAIL COMMUNICATION TYPE | - Chossing NET sends emails messages over network - Choosing CELL sends emails messages via cellular communications | ||||||||||||||||||||
| 5.11 | O/C EMAIL | Yes: Allows panel to send opening and closings reports via email | ||||||||||||||||||||
| 5.12 | O/C SMS | Yes: Allows the panel to send messages via SMS (Text Messenging) protocol | ||||||||||||||||||||
| 5.13 | MONTHLY LIMIT | This number limits the monthly incoming and outgoing SMS messages allowed to be sent or recieved by the panel | ||||||||||||||||||||
| 5.14 | SMTP SERVER | Enter the SMTP (Simple Mail Transfer Protocol) Server name. The SMTP email server is responsible for sending the email to its destination | ||||||||||||||||||||
| 5.15 | SMTP PORT | The SMTP server port number is the port that the panel uses to initiate a TCP connection with the email server. The Default port is 25 | ||||||||||||||||||||
| 5.16 | SMTP USERNAME | Most SMTP servers require a username to send email. This will be sent to the SMTP server in conjunction with the SMTP Password to provide email authentication to the server | ||||||||||||||||||||
| 5.17 | SMTP PASSWORD | Most SMTP servers require a username to send email.This will be sent to the SMTP server in conjunction with the SMTP Username to provide email authentication to the server | ||||||||||||||||||||
| 5.18 | FROM EMAIL ADDRESS | Enter the email address on file with the email service. This will show up in the email messages as the sender's address | ||||||||||||||||||||
| Device Setup | ||||||||||||||||||||||
| 6.1 | DEVICE SETUP | This is the section allows you to define the XT30/XT50 panel keypad configuration | ||||||||||||||||||||
| 6.2 | DEVICE NUMBER | Enter the device number of the keypad you are programming. The valid range is 1-8 | ||||||||||||||||||||
| 6.3 | DEVICE NAME | This section allows you to define a 16 character alphanumeric name for the device number. If no name is entered, "UNUSED" is displayed | ||||||||||||||||||||
| 6.4 | WIRELESS | Select: Yes to use a wireless keypad Select: No to use a wired keypad NOTE: You can install and address up to four wireless keypads | ||||||||||||||||||||
| 6.5 | SERIAL NUMBER | I__I__I__I__I__I__I__I__I Enter the eight digit serial number found on the wireless keypad | ||||||||||||||||||||
| 6.6 | SUPERVISION TIME | Press any top row key to Select the supervision time required for the device. Press (Command) to accept the default time. Default is 240 minutes | ||||||||||||||||||||
| 7.1. | Remote Options | |||||||||||||||||||||
| 7.2 | REMOTE KEY | Download access code, can be up to eight digits. Default is blank To enter a new remote key, press any select key and enterany combination of up to 8 digits. The numbers you enter will appear as asterisks. Press (Command) | ||||||||||||||||||||
| 7.3 | MFG AUTH | Yes: Allows DMP serice techs to access the panel when required during system service or troubleshooting. This automatically expires within one hour | ||||||||||||||||||||
| 7.4 | ARMED RINGS | Default is 8. This is how many rings it will take for the panel to pick up during the downloading procedure | ||||||||||||||||||||
| 7.5 | DISARM RINGS | Enter the number of rings the panel counts before answering the phone line | ||||||||||||||||||||
| 7.6 | ALARM RECIEVER | Yes No | ||||||||||||||||||||
| 7.7 | SERVICE RECIEVER | YES enables remote commands and programming to be accepted from a secondary service receiver other than the alarm SCS-1R Receiver. The Remote Key option can also be required. With YES selected, the panel requests the service receiver key the first time it is contacted by the service receiver. The panel retains this service receiver key in memory and accepts remote commands from the service receiver If an alarm occurs during a remote connect, the panel disconnects from the service receiver and calls the alarm receiver. Alarm reports are only sent to the alarm receiver. It is important that the alarm receiver key and the service receiver key programmed at the central station are NOT the same so the panel can determine the difference between receivers When NO is selected, remote commands and programming are not accepted from a secondary service receiver. | ||||||||||||||||||||
| 7.8 | REMOTE DISARM | Enter YES to enable the panel to be disarmed remotely Selecting NO disables remote disarming | ||||||||||||||||||||
| 8.1. | System Reports | This function allows you to select the reports the XT30/XT50 sends to the receiver | ||||||||||||||||||||
| 8.2 | O/C RPTS | NO - No Opening/Closing Reports are sent. YES - Sends Opening/Closing Reports for each programmed area. | ||||||||||||||||||||
| 8.3 | ABORT REPORTS | Yes This option allows you to specify whether the panel sends zone restoral reports and also when they will be sent.
NO - Restoral reports are not sent by the panel.
YES - The panel always sends zone restoral reports at the time the zone restores from an alarm or trouble condition.
DISARM - The panel sends zone restoral reports when a zone that has restored from an alarm or trouble is disarmed. Twenty-four hour zones send restorals immediately No | ||||||||||||||||||||
| 8.4 | ZONE RESTORALS REPORTS | This option allows you to specify whether the panel sends zone restoral reports and also when they will be sent. NO - Restoral reports are not sent by the panel. YES - The panel always sends zone restoral reports at the time the zone restores from an alarm or trouble condition. DISARM - The panel sends zone restoral reports when a zone that has restored from an alarm or trouble is disarmed. Twenty-four hour zones send restorals immediately | ||||||||||||||||||||
| 8.5 | BYPASS REPORTS | YES allows the panel to send all zone bypass, reset, and force arm reports to the receiver. The bypass report includes the zone number, zone name, and the user number of the individual bypassing the zone | ||||||||||||||||||||
| 8.6 | CODE CHANGE REPORTS | YES allows the panel to send all code additions, changes, and deletions to the receiver. The code change report includes the user number added or deleted and the user number of the individual making the change. | ||||||||||||||||||||
| 8.7 | AMBUSH | YES allows an ambush report to be sent any time user code number one is entered at a keypad. Selecting NO disables the ambush report and allows user code number one to operate the same as all other codes | ||||||||||||||||||||
| 8.8 | LATE TO OPEN | Enter 1-240 as the number of minutes to elapse that the system may remain armed after the opening time of a schedule without sending a Late To Open message. If the system continues to be armed after the Late to Open minutes expire, a Late To Open message is sent to the central station. Default is 0, which disables the Late To Open option | ||||||||||||||||||||
| 8.9 | EARLY TO CLOSE | Enter 1-240 as the number of minutes that the system can be armed prior to the scheduled closing time. If the system is armed prior to the Early to Close minutes, an Early To Close message is sent to the central station. Default is 0, which disables the Early to Close option | ||||||||||||||||||||
| 9.1. | SYSTEM OPTIONS | This section allows you to select system wide parameters used in the operation of the XT30/XT50 system. A description of each System Option follows | ||||||||||||||||||||
| 9.2 | SYSTEM | This configures the panel as either a six Area system, an All/Perimeter system (Perimeter/Interior), or a Home/Away system (Perimeter, Interior, and Bedrooms). Zones must be assigned to Bedrooms for the area to be active. When using wireless zones for an Area or All/Perimeter system, the keypad trouble buzzer resounds every four hours when wireless zone trouble or wireless low battery is displayed | ||||||||||||||||||||
| 9.3 | CLOSING CODE | When YES is selected, a code number is required for system arming. If NO is selected, a code number is not required for system arming. Default is NO | ||||||||||||||||||||
| 9.4 | CLOSING CHECK | Select YES to enable the panel to verify that all areas have been armed after a schedule expires. If the Closing Check finds any areas disarmed past the scheduled time, all keypads emit a steady beep and display CLOSING TIME!. The user must extend the schedule or arm the system within 10 minutes or a Late to Close message will be sent to the central station. Default is NO | ||||||||||||||||||||
| 9.5 | ENTRY DELAY 1 | Enter the entry delay time for all exit type zones programmed to use Entry Delay 1. When an armed Exit type zone is faulted, the keypad prewarn tone begins sounding. ENTER CODE:- and the name of the zone causing the Entry Delay displays on all keypads. When the first digit of a code is entered, the prewarn tone stops at the keypad. If, within five seconds, a valid user code is not entered or an invalid user code is entered, the prewarn tone begins sounding again. Fifteen seconds must elapse before entering a digit silences the prewarn tone again. The area must be disarmed before the entry delay expires or an will be detected. All Burglary type zones in all areas are delayed along with the Exit zone. Entry delay times can be from 30 to 250 seconds. Repeat the above for Entry Delay 2 if it is being used. Default is 30 seconds for Entry Delay 1. Note: Specific Exit Error operation is based on the Entry Delay used (1 or 2) with an EX type zone. See Exit Delay. | ||||||||||||||||||||
| 9.6 | EXIT DELAY | Enter the Exit Delay time for all Exit type zones. When the exit delay time starts, all activity on exit and burglary zones is ignored until the exit delay expires. The keypad displays the Exit Delay time countdown and annunciates the Exit Delay tone at 8 second intervals until the last 10 seconds when annunciation is at 3 second intervals. The exit delay can be from 45 to 250 seconds. Default is 60 seconds. During Exit Delay, if an exit zone trips, then restores, and trips again, the Exit Delay timer restarts. This restart can occur only once. Exit Error Operation: At arming, when an entry/exit zone (EX) is faulted at the end of the exit delay then one of two sequences occur: For Entry Delay 1 EX type zones: - the bell sounds for the length of time set in Bell Cutoff programming - the Entry Delay operation starts, requiring code entry to disarm - if not disarmed, a zone alarm and an Exit Error are sent to the receiver. For Entry Delay 2 EX type zones: - the zone is force armed and a zone force arm message is sent to the receiver - an Exit Error is sent to the receiver - the bell sounds for the length of time set in Bell Cutoff programming | ||||||||||||||||||||
| 9.7 | CROSS ZONE TIME | Enter the time allowed between zone faults. When a zone programmed for cross zoning faults, the panel begins counting down the Cross-Zone Time entered here. If the same zone or another cross-zoned zone faults within this time, an alarm report is sent to the receiver. If the Cross-Zone Time expires without the second zone fault, only a zone fault report from the first zone is sent to the receiver. The Cross-Zone Time can be from 4 to 250 seconds in one second increments. Enter 0 (zero) to disable the Cross-Zone Time feature. See the Appendix | ||||||||||||||||||||
| 9.8 | POWER FAIL DELAY | This option tracks the duration of an AC power failure. The delay time can be from 1 to 9 hours. When the AC power is off for the length of the programmed delay time, an AC power failure report is sent to the receiver. For example, if the power failure delay is set for two hours, then the AC power failure report will be sent between 2-3 hours. Entering a 0 (zero) sends the AC power failure report within 15 seconds | ||||||||||||||||||||
| 9.9 | SWINGER BYPASS TRIPS | Enter the number of times (1-6) a zone can go into an alarm or trouble condition within one hour before being automatically bypassed. Bypassed zones are automatically reset when the area they are assigned to is disarmed. All 24-hour zones are reset when any area of the system is disarmed. A programming Stop operation restores a bypassed zone. Entering 0 (zero) disables this function. Default is 2. How it works The panel hour timer starts at 59 minutes past the hour. If the hour timer expires before the trip counter is exceeded, the trip counter returns to 0 (zero). If the trip counter is exceeded before the hour expires, the zone is automatically bypassed by the panel. A Bypass Report is sent to the receiver if Bypass Reports is YES | ||||||||||||||||||||
| 9.10 | RESET SWINGER BYPASS | When YES is selected, an automatically bypassed zone is reset if it remains in a normal condition for one complete hour after being bypassed. A report of the automatic reset is sent to the receiver if Bypass Reports has been selected as YES. Default is NO | ||||||||||||||||||||
| 9.11 | TELEPHONE ACCESS | YES allows the use of standard DTMF telephones to arm and disarm and check the armed status of the XT30/XT50 panel. Refer to the XT30 or XT50 User’s Guide for complete information | ||||||||||||||||||||
| 9.12 | ZONE ACTIVITY HOURS | This option provides supervision of a person living alone for non-activity. Enter the number of hours, 0 to 9, allowed to elapse without a disarmed zone being tripped before a message is sent to the receiver. Default is 0 (zero). When the system is disarmed, the timer begins to countdown the number of hours programmed. Each time activity occurs, the timer restarts the countdown. Before the countdown time expires, the keypad sounds a tone and PRESS ANY KEY displays to allow the user to restart the activity timer. The duration of the tone is the number of seconds programmed for Entry Delay 2. Select the SUPV/TRBL receiver option in communication programming to send S93 ALARM: User Activity Not Detected, S94 Alert: Activity Check Enabled, and S95 Alert: Activity Check Disabled messages. When an open/close schedule is programmed, the timer only counts down during the scheduled open period. Also, when a schedule is programmed, if the timer is counting down and the scheduled open time occurs, the timer resets and begins the countdown again | ||||||||||||||||||||
| 9.13 | ARM ACTIVITY DAYS | This allows selection of the number of days a countdown timer is set for area arming and disarming activity. The range for the countdown timer is 00 to 99. When the timer counts down to zero because of no arming or disarming activity, the panel sends a “No Arming/Disarming” message to the receiver at 10:00 AM. Each time an area is armed or disarmed, the timer is restarted. When the countdown timer expires because of no arming or disarming activity, and a message is sent, the timer does not restart until a panel reset occurs or an area is armed or disarmed. The SUPV/TRBL receiver option must be selected in communication programming for the message to be sent | ||||||||||||||||||||
| 9.14 | TIME ZONE CHANGES | This option allows the panel to request automatic time changes from the DMP
SCS-1R Receiver. For the receiver to send time changes, it must be programmed to send time changes and must be receiving time change updates from the host automation computer at least every 24 hours. Default is YES. When time zone is programmed YES, enter the number (0-23) that indicates the Greenwich Time zone (GMT) where the panel is located | ||||||||||||||||||||
| 9.15 | TIME DISPLAY | This option allows the panel to request automatic time changes from the DMP SCS-1R Receiver. For the receiver to send time changes, it must be programmed to send time changes and must be receiving time change updates from the host automation computer at least every 24 hours. Default is YES. Hrs from GMT: 6 When time zone is programmed YES, enter the number (0-23) that indicates the Greenwich Time zone (GMT) where the panel is located. The default is 6. See table below for GMT values. | ||||||||||||||||||||
| 9.16 | HOUSE CODE | When using a DMP wireless system, enter a house code between 1 and 50 for the wireless system to use. The DMP wireless receiver automatically programs the house code into the wireless transmitters when the unique transmitter serial number is programmed into the panel. See Wireless programming in Zone Information. Default is 0 (zero) indicating the DMP wireless system is not being used. The house code identifies the panel, receiver, and transmitters to each other. When operating, the receiver listens for transmissions that have the programmed house code and transmitter serial number. Note: The flexibility of DMP two-way wireless operation allows an existing house code to be changed in the panel at any time. The transmitter may take up to two minutes to learn the new house code and continue operation. Note: When any wireless zone programming is changed in the panel, wireless receiver zone programming is updated by the panel. At that point, all wireless zones display as normal for up to 1 minute, regardless of the actual state of the zone | ||||||||||||||||||||
| 9.16.1 | DETECT WIRELESS JAMMING | This option displays when the House Code entered is for a DMP 1100D Series Wireless system. When enabled and the receiver detects jamming, a trouble or alarm message is sent to the receiver and displays in the Status List. Select YES to enable jamming messages to display in the Status List. Select NO to disable jamming messages. Default is NO | ||||||||||||||||||||
| 9.16.2 | WIRELESS AUDIBLE ANNUNCIATION | This option displays when the House Code entered is for a DMP 1100D Series Wireless system (1-50). Press any top row key to select the keypad buzzer annunciation method for wireless low battery and missing messages. - Select ANY to enable annunciation anytime. - Select DAY to enable annunciation except during sleeping hours (9 PM to 9 AM). - Select MIN (minimum) to annunciate only Fire and Fire Verify zones during • daytime hours (9 AM to 9 PM). Default is DAY | ||||||||||||||||||||
| 9.17 | BUILT-IN WIRELESS (XT-50 ONLY) | Select YES if using the built-in wireless receiver on the XT50. If selected, zones 80-99 are available to be programmed as wireless zones in addition to any keypad zone number. Select NO to use an external 1100 series wireless receiver. If NO is selected, address 8 is useable with zones 81-84 for hardwire or wireless operation, but zones 80 and 85-99 are not available. Default is YES | ||||||||||||||||||||
| 9.18 | ENABLE KEYPAD PANICS | This option allows the two-button panic key operation selected at a keypad to send the Panic, Emergency, or Fire message to the central station receiver. Select YES to enable the two-button panic operation. To disable the two-button panic operation, select NO. Default is YES | ||||||||||||||||||||
| 9.19 | OCCUPIED PREMISIS | Select YES to allow the panel to automatically disarm the interior area(s) when arming all areas and a perimeter zone is not tripped during the exit delay. This False Alarm Reduction feature will keep a user from arming the entire system when they do not exit and remain in the premise. Select NO to not automatically disarm interior area(s). Default is YES | ||||||||||||||||||||
| 9.20 | TIME DISPLAY | Select YES to display IS THIS A FALSE ALARM? NO YES at the keypad in place of CANCEL VERIFY when a burglar alarm occurs. This operates for ALL/PERIM and HOME/SLEEP/AWAY arming systems. Default is NO | ||||||||||||||||||||
| 10.1. | BELL OPTIONS | This section allows you to program the panel bell output functions. If using the Model 1135 Wireless Siren for local annunciation, the Trip with Panel Bell option should be selected in the Output Information programming for the siren | ||||||||||||||||||||
| 10.2 | BELL CUTOFF | Enter the maximum time from 1 to 15 minutes the Bell Output remains on. If the Bell Output is manually silenced or the system is disarmed, the cutoff time is reset. Enter zero to provide continuous bell output. Default is 5. Note: To support the Cancel/Verify operation on an All/Perimeter or Home/Sleep/Away system, set the Bell Cutoff Time to greater than 0 | ||||||||||||||||||||
| 10.3 | AUTOMATIC BELL TEST | When YES is selected, the Bell Output is turned on for two seconds when all areas in the system are armed. The Bell Test only occurs when the areas are armed from a keypad. Arming performed from an Arming zone or remotely from Remote Link™ does not activate the Bell Test. In addition, the Closing Wait feature is activated if Opening/Closing Reports is YES. See OPENING/CLOSING AND USER REPORTS. Closing Wait operation Closing Wait provides a delay time before a monitored system arms until the panel receives an acknowledgment of the closing report from the central station receiver. During the delay, the keypad displays ONE MOMENT . . . Once the closing is acknowledged, the keypad buzzes for one second and then displays the ALL SYSTEM ON message. If the primary communication fails, but the backup communication is successful, then the message BACKUP ALR ONLY appears. If both primary and backup communication fail, the message LOCAL ALARM ONLY will appear | ||||||||||||||||||||
| 10.4 | BELL OUTPUT | Enter the output number when needed to follow the panel Bell terminal 5 operation for all action and off conditions. Enter 0 (zero) to disable. Note: When BELL ACTION below is set to T for Temporal Code 3, this Bell Output action is pulse for wired outputs 1-4 and wireless outputs 31-34 and 41-44 | ||||||||||||||||||||
| 10.5 | BELL ACTION | This defines the type of Bell Action from zone alarms that occurs on the panel’s bell terminal number 5. Trouble conditions do not activate Bell Action. There are seven zone types you can program individually for Bell Output. To provide a steady Bell Output, enter S. For a pulsed output, enter P. For a Temporal Code 3 output, enter T and for no Bell Output, enter N | ||||||||||||||||||||
| 10.5.1 | FIRE | Defines Bell Action for Fire Type Zones. The default is set at P | ||||||||||||||||||||
| 10.5.2 | BURGULARY | Defines Bell Action for Burglary Type Zones. The default is set at S | ||||||||||||||||||||
| 10.5.3 | SUPERVISORY | Defines Bell Action for Supervisory Type Zones. The default is set at N | ||||||||||||||||||||
| 10.5.4 | PANIC | Defines Bell Action for Panic Type Zones. The default is set at N | ||||||||||||||||||||
| 10.5.5 | EMERGENCY | Defines Bell Action for Emergency Type Zones. The default is set at N | ||||||||||||||||||||
| 10.5.6 | AUXILIARY 1 | Defines Bell Action for Auxiliary 1 Type Zones. The default is set at N | ||||||||||||||||||||
| 10.5.7 | AUXILIARY 2 | Defines Bell Action for Auxiliary 2 Type Zones. The default is set at N. | ||||||||||||||||||||
| 11.1 | OUTPUT OPTIONS | collector) outputs are available using the 4-wire output harness on the XT30/XT50 board. Wireless outputs are available when using the built-in 1100 Series Receiver of the XT50 or an 1100D Series Wireless Receiver. Refer to the XT30/XT50 Installation Guide (LT-0624) for complete information. Select from the following output numbers: • 1 to 4 • 31 to 34 • 41 to 44 | ||||||||||||||||||||
| 11.2.1 | CUTOFF OUTPUTS | This option allows you to define the operation of the four on-board annunciator outputs. For each programming option, enter the number of the output you wish to activate or 0 (zero) for no output. Any or all of the available outputs can be programmed here to turn off after the time specified in Output Cutoff Time. See the Output Cutoff Time section for additional information. To disable this option, press any Select key to clear the display of output numbers and then press COMMAND. Note: Whenever an output is assigned in Output Options, that output cannot be turned on from the User Menu | ||||||||||||||||||||
| 11.2.2 | OUTPUT CUTOFF TIME | If a Cutoff Output is assigned, you can enter a Cutoff Time for the output to remain on up to 15 minutes. If the output is turned off manually, the cutoff time is reset. The Cutoff Time can be 1 - 15 minutes. Enter 0 (zero) to provide continuous output. Note: The output is cutoff within 60 seconds of the programmed cutoff time. The Cutoff Timer is shared by all outputs. If a second output trips, the timer is not reset. Both outputs turn off when the original time expires | ||||||||||||||||||||
| 11.3 | COMMUNICATION FAILURE OUTPUT | This output turns on when the panel fails to communicate with the receiver after three successive dial attempts. Enter 0 (zero) to disable this output. Note: To turn off the Communication Failure Output, disarm the panel or turn the output off using the User Menu Outputs On/Off function | ||||||||||||||||||||
| 11.4 | FIRE ALARM OUTPUT | This output turns on any time a fire type zone is placed in alarm. The output turns off using the Sensor Reset option when no additional fire type zones are in alarm. Enter 0 (zero) to disable this output | ||||||||||||||||||||
| 11.5 | FIRE TROUBLE | This output turns on any time a fire type zone is placed in trouble or when a supervisory type zone is placed in alarm or trouble. The output turns off when all fire and supervisory type zones restore to normal. Enter 0 (zero) to disable | ||||||||||||||||||||
| 11.6 | AMBUSH OUTPUT | This output turns on any time an Ambush code is entered at a keypad. The output turns off using the Sensor Reset option. Enter 0 (zero) to disable this output | ||||||||||||||||||||
| 11.7 | ENTRY OUTPUT | This output turns on at the start of the entry delay time. The output turns off when the area disarms or the entry delay time expires. Enter 0 (zero) to disable | ||||||||||||||||||||
| 11.8 | EXIT OUTPUT | This output turns on any time an exit delay time starts. The output turns off when the system arms or when the arming has been stopped. Enter 0 (zero) to disable | ||||||||||||||||||||
| 11.9 | READY OUTPUT | This output turns on whenever all disarmed zones are in a normal state. The output turns off when any disarmed zone is in a bad state. Enter 0 (zero) to disable | ||||||||||||||||||||
| 11.10 | ARMED OUTPUT | This output turns on any time an area of the system arms. The output turns off when the system completely disarms. Enter 0 (zero) to disable this output | ||||||||||||||||||||
| 11.11 | BURGUALRY OUTPUT | This output turns on any time a burglary zone goes into alarm. The output turns off when the area in which the alarm occurred disarms and no other burglary zones are in alarm. Enter 0 (zero) to disable this output | ||||||||||||||||||||
| 11.12 | LATE TO CLOSE OUTPUT | Enter the output number to turn on at the expiration of a closing schedule when all areas are not armed. The output activates simultaneously with the CLOSING TIME! keypad display. The output is turned off when all areas are armed, the closing is extended, or the schedule is changed | ||||||||||||||||||||
| 11.13 | ARM-ALARM OUTPUT | Enter the output number to turn on steady when any area of the system is armed. If an alarm occurs causing the keypads to turn Red, this output pulses and continues to pulse for approximately three (3) minutes after the panel is disarmed. Enter 0 (zero) to disable. Wireless Outputs: - The Arm-Alarm Output is compatible with the Model 1117 Wireless LED Annunciator and the Model 1116 Wireless Relay Output connected to a Model 572 Indicator LED. - When the Model 1117 is battery operated, the LED is off when the system is armed to conserve battery life. If an alarm occurs, the output flashes quickly. - When using the Model 1116 connected to a Model 572, the LED is on when the system is armed. If an alarm occurs, the output pulses. - To operate the Arm-Alarm output within one second, program a fast response number from 41 to 44. Fast response operation reduces overall wireless output battery life. - To operate the Arm-Alarm output within 15 seconds, program a slow response number from 31 to 34. Slow response operation increases overall wireless output battery life | ||||||||||||||||||||
| 12.1 | OUTPUT INFORMATION | This section allows you to program and name wireless outputs into the panel when using an 1100D/1100DH/1100DI Wireless Receiver or the built-in receiver of the XT50. Wireless outputs are also available on the XT50 when using an onboard receiver | ||||||||||||||||||||
| 12.2 | Enter an output number. Select from the following output numbers: • 1 to 4 • 31 to 34 — Slow response time* wireless outputs (activate within 15 seconds) • 41 to 44 — Fast response time* wireless outputs (activate within 1 second) Note: Addresses 31 to 34 and 41 to 44 are available for wireless outputs, keypad bus zones, wireless zones or wireless key fob zones and can only be assigned to one device. * The response time of a wireless output is the time it takes for a wireless output to activate once the panel event occurs. You determine whether a wireless output is a slow or fast response based on the output number assigned. A slow response output number extends battery life, but response time may be up to 15 seconds. A fast response output number responds within 1 second, but reduces battery life. Refer to the specific wireless output installation guide to determine battery life | |||||||||||||||||||||
| 12.3 | OUTPUT NAME | This section allows you to define a 16 character alphanumeric name for any output numbers.
Hardwired outputs (Output Numbers 1-4) default to the number of the output. Press a top row Select key to enter a name. Wireless outputs (Output Numbers 31-34 and 41-44) are initially named *UNUSED* and are not part of the system until they are assigned a name. Press a top row Select key to enter a name. To mark a wireless output unused, delete the old name by pressing any Select key, then press the COMMAND key. The programmer automatically programs the name as * UNUSED * | ||||||||||||||||||||
| 12.4 | SERIAL NUMBER | Enter the eight-digit serial number found on the wireless device | ||||||||||||||||||||
| 12.5 | SUPERVISION TIMER | Press any top row key to select the supervision time required for the wireless output. Press COMMAND to accept the default time. Default is 240 minutes Select the required number of minutes. The transmitter must check in at least once during this time or a missing condition is indicated for that zone. 1100 Series transmitters automatically check in based on the supervision time selected for the wireless zone, no additional programming is needed. Zero (0) indicates an unsupervised transmitter. The 3 minute supervision time is only available if using an 1135 Wireless Siren. Note: When the panel is reset, a receiver is installed or powered down and powered up, or programming is complete, the supervision timer restarts for all wireless outputs | ||||||||||||||||||||
| 12.6 | TRIP WITH PANEL BELL OPTION | This option displays when the wireless device is an 1135 wireless siren. Select YES to have the 1135 wireless siren follow the panel’s bell output cadence for the zone type and bell cutoff time. Default is YES | ||||||||||||||||||||
| 13.1 | AREA INFORMATION | This section allows you to assign functions to individual areas for XT30 and XT50 panels. All non-24-hour zones must be assigned to an active area. See the section on Zone Information. Activate an area by assigning it a name. A name is given to each active area in place of a number to assist the user during arming and disarming | ||||||||||||||||||||
| 13.2 | AREA NUMBER | |||||||||||||||||||||
| 13.3 | AREA NAME | In an area system, enter up to 16 characters for the area name. Only those areas given names can have zones assigned to them. All others are marked *UNUSED*. Refer to the Entering Alpha Characters section. To add an area name to the system, press any Select key and then enter up to 16 characters for the new name. Press COMMAND to continue. To mark an active area as unused, delete the old name by pressing any Select key then press the COMMAND key. The panel automatically sets the name as *UNUSED*. If you have already Initialized the panel, all areas will be marked as *UNUSED*. See section 2.3 | ||||||||||||||||||||
| 13.4 | AUTOMATIC ARMING | Select YES to allow this area to arm automatically according to the opening and closing schedule. If Closing Check is selected as YES, the automatic arming does not take place until the expiration of a 10-minute Closing Check delay. If the area has been disarmed outside a schedule, the Closing Check delay occurs one hour after the area is disarmed. At arming, faulted zones are handled according to the option selected in Bad Zones. If a Closing report is sent, the user number is indicated as SCH on the SCS-1R Receiver. Select NO to disable automatic arming for this area. Default is NO. Note: For ANSI/SIA CP-01 installations, Automatic Arming cannot be used for arming | ||||||||||||||||||||
| 13.4.1 | BAD ZONES | At the time of automatic arming, some zones in the area may not be in a normal condition. This option allows you to program the panel’s response to these bad zones. This option is not displayed if AUTO ARM is NO. BYP - All bad zones are bypassed. A report of the bypass is sent to the receiver if Bypass Reports has been selected as YES. See the Bypass Reports section. The report indicates SCH as the user number. FORC - All bad zones are force armed. Zones force armed in a bad condition are capable of restoring into the system and reporting alarms if tripped. A report of the force arm is sent if Bypass Reports is YES. See the Bypass Reports section. The report indicates the user number as SCH. REF - The automatic arming is refused and no arming takes place. A No Closing report is sent to the receiver regardless of the Closing Check selection. See the XT30 and XT50 Programming Sheets. Note: For NRTL listed installations, set Bad Zones to REF | ||||||||||||||||||||
| 13.5 | AUTOMATIC DISARMING | NO disables automatic disarming by schedule for this area. Select YES to allow this area to automatically disarm according to a schedule. If an Opening report is sent to the receiver, the user number is indicated as SCH. Note: For ANSI/SIA CP-01 installations, Automatic Disarming cannot be used | ||||||||||||||||||||
| 14.1 | ZONE INFORMATION | This allows you to define the operation of each protection zone used in the system. | ||||||||||||||||||||
| 14.2 | ZONE NUMBER |
Note: Use zone numbers 31 to 34 or 41 to 44 with 1100 Series Key Fobs or DMP wireless output modules. The XT50 has 20 onboard wireless zones numbered 80-99 and can be programmed to use zones 11-84 as wireless. When using the XT50 built-in 1100 Series Receiver, any keypad bus zone can be programmed as wireless while the next consecutive zone number can be hardwire from a keypad or zone expander. Note: When using 1101, 1105, or 1114 devices, do not use the consecutive zones 80-81 or 84-85. When using the XT30/XT50 panel with a keypad bus wireless receiver and any wireless input zone for a particular device address is programmed (Ex: 11‑14 = Addr 1), the 1100D/1100DH/1100DI responds to the panel for this entire address. Other devices, such as keypads or hardwired zone expanders, cannot use this address. Zones connected directly to the panel cannot be wireless | ||||||||||||||||||||
| 14.3 | KEY FOB | Select YES to program an 1100 Series Key Fob for zones 31-34 or 41-44. When YES is selected, programming continues at the 1100 Series Key Fobs Section. Default is NO | ||||||||||||||||||||
| 14.4 | ZONE NAME | Press any Select key and enter up to 16 characters for the zone name. A name must be given to each zone in the system. This name can be displayed at the keypads when the zone is bad or viewed in Display Events. The zone name is also sent to the receiver as part of a zone event report. A zone that is not part of the system must be marked *UNUSED*. To mark a zone unused, delete the old name by pressing any Select key, then press the COMMAND key. The programmer automatically programs the name as * UNUSED *. If you selected ZONES? NO YES to clear the panel’s memory during Initialization, the zones will already be marked * UNUSED *. See the Initialization section. | ||||||||||||||||||||
| 14.5 | ZONE TYPE | The Zone Type defines the panel’s response to the zone being opened or shorted. Refer to the Appendix for zone type defaults and descriptions.
When you assign a Zone Type to a zone, responses are made automatically for the zone. There are 11 Zone Types to choose from including Blank. The functional details of each response are described in Zone Type Defaults in the Appendix.
To select a new Zone Type, press any Select key. The display lists the four Zone Types shown below. When the Zone Type you want to select displays, press the Select key below the name. Blank, Night, Day, or Exit. Press COMMAND to display additional zone types. Fire, Panic, Emergency, or Supervisory. Press COMMAND to display additional zone types. Auxiliary 1, Auxiliary 2, Fire Verify, or Arming. Press the Back Arrow key to display the previous zone types If you select Blank, Night, Day, Exit, Auxiliary 1, or Auxiliary 2 as the Zone Type, the zone must be assigned to an area. If you select Fire, Panic, Emergency, or Supervisory as the Zone Type, these are 24-hour zones that are always armed and no area assignment is needed. Press COMMAND to continue. CAUTION: When a sensor reset is performed at the keypad, power will drop to devices connected to zone 10 causing the panel to sense an open condition on all zone types other than Fire (FI), Fire Verify (FV), and Supervisory (SV). Whenever non-Fire and non-Supervisory zone types are used on zone 10, make the appropriate adjustments to the zone Armed Action to prevent false alarms from occurring. Refer to the Appendix for zone type specifications and descriptions. Note: For listed installations using wireless zones, do not use the FV zone type | ||||||||||||||||||||
| 14.6 | AREA ASSINGMENT | For Area systems, enter the area number from 1 to 6 where this zone is being assigned For All/Perimeter systems, choose INTERIOR or PERIMETER For Home/Away systems, choose INTERIOR, PERIMETER, or BEDROOMS. - INT (Interior) - Assigns the zone to area 2, Interior - BDRM (Bedroom)- Assigns the zone to area 3, Bedrooms. This option is only displayed in Home/Away systems. - PERIM (Perimeter) - Assigns the zone to area 1, Perimeter | ||||||||||||||||||||
| 14.7 | ARMING ZONE ASSIGNMENTS | For Area systems, this option specifies the areas to be armed by the Arming Type zone. Press the appropriate number keys on the keypad to assign areas 1 to 6. When disarmed, all programmed areas are disarmed - For All/Perimeter systems, choose PERIM or ALL. For Home/Away systems, choose HOME, SLEEP, or AWAY -Perimeter/All - Specify whether the arming zone arms just the Perimeter (PERIM) or the Perimeter and Interior areas (ALL) for All/Perimeter systems. When disarming, all areas are disarmed HOME/SLEEP/AWAY - Specify whether the arming zone arms the Perimeter (HOME), the Perimeter and Interior (SLEEP), or all three areas (AWAY). When disarming, all areas are disarmed Arming zone operation If a bad (faulted) Priority zone is in the area being armed by an Arming zone, the arming is stopped. If there are no Priority zones, or they are all in a normal condition, the following applies: When a non-Priority zone is bad when an area is armed with a keyswitch on an Arming zone, the arming is delayed for five seconds. If, during the five-second delay, the keyswitch is turned to disarm, the arming stops. If the keyswitch is held in the arming position for the full five seconds, the bad zone is force armed and the area is armed. The ability to stop the arming does not apply if a wireless arming device is being used. Refer to the Appendix. Note: Arming from a zone, voice module, touch tone telephone, or Remote Link is not affected by this operation | ||||||||||||||||||||
| 14.7.1 | STYLE | |||||||||||||||||||||
| 13.2 | SERIAL NUMBER | |||||||||||||||||||||
| 13.2 | SERIAL NUMBER | |||||||||||||||||||||
| 13.2 | SERIAL NUMBER | |||||||||||||||||||||
| 13.2 | SERIAL NUMBER | |||||||||||||||||||||
| 13.2 | SERIAL NUMBER | |||||||||||||||||||||
| 13.2 | SERIAL NUMBER | |||||||||||||||||||||
| 13.2 | SERIAL NUMBER | |||||||||||||||||||||
| 13.2 | SERIAL NUMBER |